3M VHB 5608 Double Sided Acrylic Foam Adhesive Tape Waterproof Heavy Duty Mounting Tape For Car Indoor Outdoor Use Free Shipping


Price in reward points: 2
  • Brand: 未设置品牌
  • Product Code: sew230707683540
  • Availability: In Stock

- +

3M x 5mm 6mm 8mm 10mm 12mm 15mm 20mm 3M high temperature transparent acrylic foam tape ,Clear VHB Acrylic Foam Tape 0.8MM Thick For Car /office/Home decoratron

- Brand New and High quality.
- Designed for the attachment of a wide variety of automotive exterior and interior trim including body side moldings, claddings, rock panel trim, wheel flares, bumper trim and most other automotive trim/Home Decorations.
- Strong adhesion to automotive substrates.
- Weather and car wash resistant.
- Confortable. Can be used on textured surfaces, such as painted cement or brick.
- High-strength core maintains a thin, consistent bond line.
- Easy liner release.
- Perfect to use on LED strip mounting at indoor or outdoor (included bathroom).

Hwo to use this tape?

Clean: For maximum bond strength,the surface must be clean, dry, smooth, have no rust and oil pollution.Typical cleaning solvents are heptane or isopropyl alcohol.

Pressure: Pressure on the adhesive and the surface can help improve bond strength, roller or platen can be used.

Time: After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hoursand 100% after 72 hours.

Temperature:Ideal application temperature range is 70°F to 100°F (21degree centigrade to 38degree centigrade).Operating temperature should not be below 10 degree centigrade, the temperature is too low, will lead to cure time longer. If temperature is too low, move material and adhesive tape into the warm indoor storage or heating treatment.

Q. What percent of the final bond strength can I expect immediately after application? After 24 hours? After 72 hours?

A. Immediately after an application is made, about 60% of the bond strength is achieved. As the adhesive continues to wet-out the surface, you can expect the bond to be at about 75% - 80% after 24 hours. After 72 hours, 95%+ of the bond strength is achieved. The bond will continue to build with time.

Q. Is the tape solvent resistant?

A. Yes, 3M acrylic foam tapes are resistant to most common automotive solvents like gasoline, diesel fuel, washer solvent, etc. Solvent resistance is a function of type of solvent, time of exposure and temperature.

Q. Why doesn`t the tape feel sticky?

A. 3M`s high performance acrylic adhesives tend to be firm and dry to the touch. They are designed to bond materials other than skin. The adhesives used are designed to give optimum performance and adhesion to automotive substrates and components. The natural oils and moisture of skin can vary from person to person and affect the "thumb appeal" of the 3M Acrylic Foam Tape. To one person the tape can feel very sticky and to another it can feel much less sticky to the touch. The difference in "thumb appeal" is in the variation of the 2 individual`s skin surfaces not the adhesive.

Q. The part is not adhering to the vehicle. What might be wrong?

A. Areas to investigate for poor adhesion or performance include:

Check for surface contamination. The substrates must be clean and free of any contaminant. This is the most common cause of poor adhesion.

Check for surface match. Are the two surfaces to be bonded a good match?

Check for proper application pressure and wet-out.

Check the back of the component for flatness.

Check the installation process for proper procedures.

DIY SuppliesMetalworking
OriginMainland China
Tape TypeFilament Tape

Write a review

Note: HTML is not translated!
Bad Good

Tags: 3M VHB 5608 Double Sided Acrylic Foam Adhesive Tape Waterproof Heavy Duty Mounting Tape For Car Indoor Outdoor Use Free Shipping